ikan Uploader :
Directory : /lib/modules/4.15.0-1044-aws/build/arch/mips/txx9/
Upload File : |
| Current File : //lib/modules/4.15.0-1044-aws/build/arch/mips/txx9/Kconfig |
# SPDX-License-Identifier: GPL-2.0
config MACH_TX39XX
bool
select MACH_TXX9
select SYS_HAS_CPU_TX39XX
config MACH_TX49XX
bool
select MACH_TXX9
select CEVT_R4K
select CSRC_R4K
select IRQ_MIPS_CPU
select SYS_HAS_CPU_TX49XX
select SYS_SUPPORTS_64BIT_KERNEL
config MACH_TXX9
bool
select DMA_NONCOHERENT
select SWAP_IO_SPACE
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_SUPPORTS_BIG_ENDIAN
select COMMON_CLK
config TOSHIBA_JMR3927
bool "Toshiba JMR-TX3927 board"
depends on MACH_TX39XX
select SOC_TX3927
config TOSHIBA_RBTX4927
bool "Toshiba RBTX49[23]7 board"
depends on MACH_TX49XX
select SOC_TX4927
# TX4937 is subset of TX4938
select SOC_TX4938
help
This Toshiba board is based on the TX4927 processor. Say Y here to
support this machine type
config TOSHIBA_RBTX4938
bool "Toshiba RBTX4938 board"
depends on MACH_TX49XX
select SOC_TX4938
help
This Toshiba board is based on the TX4938 processor. Say Y here to
support this machine type
config TOSHIBA_RBTX4939
bool "Toshiba RBTX4939 board"
depends on MACH_TX49XX
select SOC_TX4939
select TXX9_7SEGLED
help
This Toshiba board is based on the TX4939 processor. Say Y here to
support this machine type
config SOC_TX3927
bool
select CEVT_TXX9
select HAS_TXX9_SERIAL
select HW_HAS_PCI
select IRQ_TXX9
select GPIO_TXX9
config SOC_TX4927
bool
select CEVT_TXX9
select HAS_TXX9_SERIAL
select HW_HAS_PCI
select IRQ_TXX9
select PCI_TX4927
select GPIO_TXX9
select HAS_TXX9_ACLC
config SOC_TX4938
bool
select CEVT_TXX9
select HAS_TXX9_SERIAL
select HW_HAS_PCI
select IRQ_TXX9
select PCI_TX4927
select GPIO_TXX9
select HAS_TXX9_ACLC
config SOC_TX4939
bool
select CEVT_TXX9
select HAS_TXX9_SERIAL
select HW_HAS_PCI
select PCI_TX4927
select HAS_TXX9_ACLC
config TXX9_7SEGLED
bool
config TOSHIBA_FPCIB0
bool "FPCIB0 Backplane Support"
depends on PCI && MACH_TXX9
select I8259
config PICMG_PCI_BACKPLANE_DEFAULT
bool "Support for PICMG PCI Backplane"
depends on PCI && MACH_TXX9
default y if !TOSHIBA_FPCIB0
if TOSHIBA_RBTX4938
comment "Multiplex Pin Select"
choice
prompt "PIO[58:61]"
default TOSHIBA_RBTX4938_MPLEX_PIO58_61
config TOSHIBA_RBTX4938_MPLEX_PIO58_61
bool "PIO"
config TOSHIBA_RBTX4938_MPLEX_NAND
bool "NAND"
config TOSHIBA_RBTX4938_MPLEX_ATA
bool "ATA"
config TOSHIBA_RBTX4938_MPLEX_KEEP
bool "Keep firmware settings"
endchoice
endif
config PCI_TX4927
bool
Kontol Shell Bypass